- stranded Cu wire : 2×0,22 mm2
- 9 mm wide tip suitable for mounting to flat surfaces with M4 screw
- material: stainless steel 1.4541
Products not found
Temperature sensor suitable for measurement of liquid and gaseous media. Tight connection of the sensor and thermowell prevents leakage of installation and enables adjustment to the thickness of insulation layer. This sensor has a spring-loaded replaceable measuring insert. Adequate for various applications, mainly on ships and vessels.
- process connection with G1/2 or M20x1,5 thread
- connection head type BA IP55, – 40÷100ºC
- sheath material: acid-resistant steel 1.4541
Retail price from $82
Read more
Available
Temperature sensor applied in industrial pipelines, pressure tanks and different industrial devices for temperature measurement of liquids and gases. Sensing element is placed directly in the thermowell.
- Temperatura range-200÷550ºC RTD
- sensing element: Pt100/Pt500/Pt1000 resistor
- process connection with G1/2 or M20x1,5 thread
- connection head type BA IP55, – 40÷100ºC
- sheath material: acid-resistant steel 1.4541
- temperature transmitter can be mounted in a connection head
Retail price from $92
Read more
Available
The Series TE Duct and Immersion Temperature Sensor can be used to monitor air or water temperature throughout a building management system or an air handler unit. Flanged duct sensors monitor the supply or return air and provide a thermistor or RTD output to the digital controller. Immersion sensors which are supplied with compression fittings are typically used to monitor the hot or chilled water lines throughout a building. Thermowells are recommended, but not required on the immersion sensors.
Retail price from $10
Read more
Available
Temperature sensor suitable for measurement of machine and device outer surface, especially their bodies, blocks, etc. For the purpose of mounting the sensor only threaded hole and M4 screw is needed.
Retail price from $36
Read more
Available
Temperature sensor suitable for temporary measurement of liquids, semifluid masses or loose materials. Portable temperature meters intended for cooperation with resistance sensors are used to read the results of measurement.
- PVC hand grip, max. operating temperature 80°C
- flat miniature plug type SMPW (2 pin) or MTP (3 pin)
- material stainless steel 1.4571
Retail price from $64
Read more
Available
LIMATHERM TOP-216 Immersion RTD Pt100/Pt500/Pt1000 -50 to 200 ºC for Heat Meters And Heating Systems
Temperature sensor suitable for measurement of liquid and gaseous media, mainly in systems for energy consumption billing.
- sensing element: Pt100/Pt500/Pt1000 resistor or J, K, N, T thermocouple
- process connection with G1/2 or M20x1,5 thread
- connection head type MA IP54, – 40÷100ºC
- sheath material: acid-resistant steel 1.4541
- temperature transmitter can be mounted in a connection head
Retail price from $89
Read more
Available
Temperature sensor applied in industrial pipelines, pressure tanks and different industrial devices for temperature measurement of liquids and gases. Sensing element is placed directly in the sheath.
- Temperatura range -200÷600ºC RTD
- sensing element: Pt100/Pt500/Pt1000 resisto
- connection head type BA IP55, – 40÷100ºC
- sheath material: acid-resistant steel 1.4541
- temperature transmitter can be mounted in a connection head
Retail price from $65
Read more
Available
Temperature sensor with band clamp for measurement of pipes and shafts. The band clamp enables sensor installation on different types of pipes and shafts which are to be measured.
- pipe band clamp diameter 16÷180 mm
- fiberglass insulation, metallic overbraid
- material: stainless steel 1.4301
Retail price from $41
Read more
Available
Mineral insulated sensor with strengthened sheath suitable for measurement of liquids, semifluid masses or loose materials with high density or flow in conditions of great vibrations.
- connection head type MA IP54, – 40÷100ºC
- temperature transmitter can be mounted in a connection head
- material: stainless steel 1.4541, 1.4571 and INCONEL
Retail price from $68
Read more
Available
LIMATHERM TOP-226 Immersion RTD Pt100/Pt500/Pt1000 -50 to 180 ºC for Heat Meters And Heating Systems
Temperature sensor suitable for measurement of liquid and gaseous media, mainly in systems for energy consumption billing.
- sensing element: Pt100/Pt500/Pt1000 resistor
- process connection with G1/2 or M20x1,5 thread
- connection head type MA, IP54 -40÷100ºC
- sheath material: acid-resistant steel 1.4541
Retail price from $83
Read more
Available
LIMATHERM TOPGB-11 Immersion RTD Pt100/Pt500/Pt1000 -200 to 150 ºC with replaceable measuring insert
This sensor is used for temperature measurement of liquid and gaseous media. The temperature sensor design (replaceable measuring insert) is suitable for various industrial applications. Replacement of the measuring insert does not cause the technological installation damage. Spring-loaded insert ensures an excellent connection with the bottom of the sensor thermowell.
- process connection with G1/2 or M20x1,5 thread
- connection head type BA IP55, – 40÷100ºC
- thermowell material: acid-resistant steel 1.4541
- temperature transmitter can be mounted in a connection head
- measuring insert: pipe or mineral insulated version
Retail price from $94
Read more
Available
Temperature sensor with low thermal inertia suitable for temperature measurement of processes, where fast response to temperature change of the measured medium is needed. Sensing element is placed directly in the sheath.
- Temperatura range -200÷550ºC RTD
- sensing element: Pt100/Pt500/Pt1000 resistor
- connection head type MA IP54, – 40÷100ºC
- sheath material: acid-resistant steel 1.4541
- temperature transmitter can be mounted in a connection head
Retail price from $66
Read more
Available
The Series TE-OND/TE-RND/TE-OSA Outdoor Temperature Sensors are offered different configurations to increase measurement accuracy by reducing radiated heat effects. For applications where the north side of the building is accessible, the TE- OND/TE-OSA can be used to protect against low levels of radiated heat.
Retail price from $29
Read more
Available
Temperature sensor suitable for measurement of pipes and shafts. Rigid sheath is joined to radiator enhancing the area of heat reception. Sensor has a band clamp that enables permanent radiator installation on pipe or shaft.
- radiator enhancing surface of heat reception with band clamp for mounting on a pipeline DN 15÷200 mm
- insulated hot junction SO
- material: brass
Retail price from $40
Read more
Available
Temperature sensor suitable for measurement of liquid and gaseous media, mainly in systems for energy consumption billing.
- stranded Cu wire 2×0,25 mm2 with double silicone insulation
- outer thermowell for sensor mounting in pipelines
- sheath material: brass
Retail price from $34
Read more
Available
This sensor is used for temperature measurement of liquid and gaseous media. The temperature sensor design (replaceable measuring insert) is suitable for various industrial applications. Replacement of the measuring insert does not cause the technological installation damage. Spring-loaded insert ensures an excellent connection with the bottom of the sensor thermowell.
- Temperatura range -200÷550ºC RTD
- sensing element: Pt100/Pt500/Pt1000 resistor
- process connection with G1/2 or M20x1,5 thread
- connection head type BA IP55, – 40÷100ºC
- sheath material: acid-resistant steel 1.4541
- temperature transmitter can be mounted in a connection head
- measuring insert: pipe or mineral insulated version
Retail price from $99
Read more
Available
Temperature sensor suitable for measurement of industrial processes. Sensing element is placed directly in the sheath.
- Temperatura range -200÷600ºC RTD
- sensing element: Pt100/Pt500/Pt1000 resistor
- connection head type BA IP55, – 40÷100ºC
- sheath material: acid-resistant steel 1.4541
- temperature transmitter can be mounted in a connection head
Retail price from $83
Read more
Available
The Series TE-SNW Weather Resistant Surface Temperature Sensor non- intrusively measures the process temperature in hot and cold water loops in buildings. In order to work with most common building controllers, the output of the sensor can be chosen from 6 different RTD and Thermistor curves.
Retail price from $41
Read more
Available
Temperature sensor suitable for measurement in hard-to-reach places and in applications requiring the use of flexible sensors with small diameters, good vibration and shock resistance, and low thermal inertia.
- mounting elements: nickel-plated brass and stainless steel
- straight or angular version
Retail price from $70
Read more
Available
Temperature sensor suitable for measurement of liquid and gaseous media, mainly in systems for energy consumption billing.
- stranded Cu wire 2×0,25 mm2 with double silicone insulation
- mounting in special seats of a valve, tees
- sheath material:brass
Retail price from $40
Read more
Available
LIMATHERM TOPSW-11 Immersion RTD Pt100/Pt500/Pt1000 -200 to 550 ºC with replaceable measuring insert
Sensor suitable for temperature measurements, primarily in industrial pressure tanks, in all these places where mounting of a threaded process connection would be problematic. The temperature sensor design (replaceable measuring insert) is suitable for various industrial applications. Replacement of the measuring insert does not cause the technological installation damage. Spring-loaded insert guarantees an excellent connection with the bottom of the sensor thermowell.
- Temperatura range 0÷540ºC RTD
- sensing element: Pt100/Pt500/Pt1000 resistor
- process connection with G1/2 or M20x1,5 thread
- connection head type BA IP55, – 40÷100ºC
- sheath material: acid-resistant steel 1.4541
- temperature transmitter can be mounted in a connection head
- measuring insert: pipe or mineral insulated version
Retail price from $164
Read more
Available
LIMATHERM TOPE-26 RTD Pt100/Pt500/Pt1000 -50 to 400 ºC for measurement of machinery and device parts
Temperature sensor suitable for measurement of movable or replaceableparts of machines and devices, e.g. bearings or injection moulds. Equipped with bayonet fitting that enables quick and easy installation in the measured element. Furthermore, the sensor has a spring that protects the flexible cable. The cap of a bayonet fitting can be easily moved across the spring enabling the adjustment of sensor immersion length.
- Temperatura range -50÷400ºC Pt100
- connector with bayonet mount
- bayonet fitting with connector– nickel-plated brass
- material: stainless steel 1.4541
Retail price from $44
Read more
Available
Temperature sensor suitable for measurement of movable or replaceable parts of machines and devices, e.g. bearings or injection moulds. Equipped with bayonet fitting that enables quick and easy installation in the measured element. Furthermore, the sensor has a spring that protects the flexible cable. The cap of a bayonet fitting can be easily moved across the spring enabling the adjustment of sensor immersion length.
- brass, atmospheric pressure
- insulated hot junction SO
- additional sheath, up to 1MPa, stainless steel 1.4541
Retail price from $45
Read more
Available
Cable sensor can be equipped with plug for connection with portable temperature meters.
- performance with head MA
- PVC hand grip max. operating temperature 80°C
- with transmitter 4÷20 mA (LTT-03J)
- material: stainless steel 1.4541
Retail price from $69
Read more
Available