OMEGA FMA1700A-1800A-Series Gas Mass Flow Meters for Clean Gases with Optional Integral Display

Description of OMEGA FMA1700A-1800A

The FMA1700A/1800A Series eletronic gas mass flow meters allow users to monitor the flow of a wide variety of gases from 10 SCCM up to 1000 SLM. Utilizing heat transfer through a heated tube to measure molecular gas flow rate, the FMA1700A/1800A provides measurement of direct gas mass flow rate, without the need to compensate for variations in gas temperature or pressure (within stated limits). They are available in an economical aluminum/brass construction for typical gas flows and a 316 SS construction for applications requiring more corrosion resistance. The FMA1700A series without integral display is supplied with a field selectable analog 0 to 5 Vdc or 4 to 20 mA output for remote monitoring; the FMA1800A series has both an integral 3½ digit display and analog output. The display is tiltable over 90 degrees for viewing convenience. The display is calibrated standard to readout directly in SCCM or SLM for nitrogen (other gas calibrations available on special order). Due to their low cost, digital display, analog output capability, and insensitivity to variations in gas temperature and pressure, the FMA1700A/1800A Series are ideal substitutes for many Variable Area Flow Meter applications. When used with the FMA178BP portable battery pack, the FMA1800A Series are ideal for in-the-field calibration of flow meters or testing of air sampling equipment. The FMA178BP battery pack includes batteries, recharger, and carrying case with shoulder strap and belt loop. With the FMA178BP, the flow meter can operate in excess of 40 hours; the batteries can be recharged at least 200 times. The FMA1700A/1800A Series require 12 to 26 Vdc power @ 200 mA maximum, which can be supplied by the FMA178PW plug-in socket power supply. The electronics are reverse polarity protected and has externally accessible fusing. Model number FMA178C (supplied separately) provides a mating 9-pin “D” connector with 3 feet of ribbon cable for accessing the 0 to 5 Vdc output signal and power input connections (use FMA178C-MA for 4 to 20 mA output signal connection). The LCD supplied with the FMA1800A Series is connected to the lower electronics via a modular plug. The LCD can be remotely located by purchasing an FMA18RC remote cable assembly you must then build your own assembly for panel mounting the LCD.

Technical specifications of OMEGA FMA1700A-1800A

• Accuracy: ±1% of full scale, including linearity over 15 to 25°C and 5 to 60 psia (0.35 to 4.2 kg/cm²)(For sizes up to 100SLM), ±1.5% of full scale, including linearity over 15 to 25°C and 5 to 60 psia (0.35 to 4.2 kg/cm²)For larger sizes)
• Turn-Down Ratio: 100:1
• Repeatability: ±0.5% of full scale and for units ≥100 scm from 0 to 20% of range
• Temperature Coefficient: 0.15% of full scale per °C or better
• Pressure Coefficient: 0.01% of full scale per psi (0.07 bar)
• Response Time: 800 msec time constant; 2 seconds (typical) to within ±2% of set flow rate over 25 to 100% of full scale
• Power Requirements:12 to 26 Vdc power @200 mA maximum
• Maximum Gas Pressure: 1000 psig (70 kg/cm² gauge) for ranges upto 100 SLM; 500 psig (35 kg/cm² gauge)Above 100 SLM; 20 psig optimum
• Gas and Ambient Temperature: 0 to 50°C (0 to 122°F)
• Leak Integrity: 1 x 10-9; std cc/sec of helium maximum to outside environment
• Materials in Fluid Contact:
  • Aluminum models: Anodized aluminum, 316 SS, brass and FKM O-rings
  • Stainless Steel models: 316 SS and FKM O-rings
• Output Signal
  • Linear 0 to 5 Vdc: 1000 Ω minimum load
  • 4 to 20 mA: 50 to 250 Ω loop resistance
• Transducer Power: 12 to 26 Vdc @ 200 mA maximum (FMA178PW)
• Shipping Weight: 1.1 kg (2.5 lb)
• Compliance: EN55011 class 1, class B; EN50082-1

How to buy OMEGA FMA1700A-1800A